Pore structure and flexural strength of ZrO2 nanopowders palm oil clinker aggregate-based binary blended concrete Farzad Soleymani Department of Metallurgical Engineering, Payame Noor University, P.O. 19395-4697, Tehran, Iran. E-mail: [email protected] Abstract: Malaysia is the largest producer and exporter of palm oil in the world.
Journal of American Science, 2012;8(5) Farzad Soleymani 61 Split tensile strength of palm oil clinker aggregates-based cementitious composites in the optimum state Farzad Soleymani Department of Metallurgical Engineering, Payame Noor University, P.O. 19395-4697, Tehran, Iran.
Palm oil clinker (POC) is a by-product of palm oil industry and its utilization in concrete production not only solves the problem of disposing this solid waste but also helps to conserve natural ...
palm oil mill effluent (POME), and palm oil mill sludge (POMS), as well as the solid wastes generated as a result from further processing of these biomasses into the palm oil fuel ashes (POFA) and palm oil clinkers (POC). An agro-industrial waste profile for palm oil mills was computed based on the thirteen years operation and production data.
This paper suggests verification for modeling of ultimate load of lightweight Palm Oil Clinker (POC) reinforced concrete (RC) beams with web openings using the Response Surface Methodology (RSM). The proposed model is developed to predict and verify the ultimate load for a comparison with the experimental measurements
lightweight concrete produced from oil palm clinker aggregates. Oil palm clinker is obtained from by-product of palm oil milling. Utilising oil palm clinker in concrete production not only solves the problem of disposing this solid waste but also help to converse natural resources. The parameter of …
Palm oil clinker (POC) is a waste by-product gathered after the complete incineration process of oil palm shell and ﬁbre. Physically they are porous, grey in colour, irregular in shape and much lighter. Most of the palm oil processing plants dispose of the clinker in them by using them
palm clinker concretes are found to be within the range of l7 to 40 MPa after 28 days of curing, which is satisfies the requirement if used as structural lightweight concrete (ASTM- C330 2004). From the previous research, it was suggested that the palm oil clinker concrete is suitable to be
The input data basically are inputs of raw materials such as oil palm fresh fruit bunches, electricity, diesel, water, fuel for boiler etc. and the output consists of the biomass wastes, palm oil mill effluents, flue gases from stack, kernel etc.
Abstract. Technical benefit of incorporation of Palm Oil Clinker (POC) in cement-based applications has been proven in recent studies. The aim of this work was to assess the heavy
palm oil clinker. In this research, the effects of using different percentage of palm oil clinker as partial sand replacement in cement sand brick were investigated. Furthermore, the properties of this newly developed palm oil clinker cement sand brick was determined. 2. Experimental Setup
Read "Performance evaluation of palm oil clinker as coarse aggregate in high strength lightweight concrete, Journal of Cleaner Production" on DeepDyve, the largest online rental service for scholarly research with thousands of academic publications available at your fingertips.
a cleaner and greener concrete, waste palm oil clinker (POC) powder, a by-product from palm oil industry was used as ﬁller and amorphous material in the development of sustainable and environmental friendly lightweight concrete. The utilization of POC powder as …
This paper presents an investigation on the fresh concrete properties using palm oil clinker as fine aggregate replacement material. The primary objective of this study is to conduct workability tests on M30 grade concrete for palm oil clinker replacement proportions of 0%, 5%, 10%, 15%, 20% and 25% by weight of fine aggregate.
29 in palm oil mill in Malaysia . Palm oil clinker (POC) is a waste material produced as result of 30 incomplete burning of palm oil shells and mesocarp fibres as fuel to run steam turbines in palm 31 oil mills. Palm oil mills produce approximately 5% by weight of the total oil palm waste at the
Palm oil clinker pervious concrete was produced. • Incorporation of palm oil clinker reduced the compressive strength and density of the concrete. • Permeability and porosity increased with addition of palm oil clinker. • Optimum performance was at 25% replacement.
the largest producers and exporters of palm oil products to various corners of the world. Plenty of waste by-products are collected throughout the palm oil processing phases. One of them is palm oil clinker (POC), which is obtained in large chunks during the oil palm shell and ﬁbre incineration process. Nowadays, POC is disposed of by landﬁll.
palm oil clinker replacement by means of experimental trays to simulate the real green roof system. It was found that palm oil clinker has a good ability of draining the excess water and there is no side effect in term of plant development. This indicates that there is a possibility of using palm oil clinker as drainage layer in green roof system.
Self-compacting lightweight concrete (SCLWC) is an innovative high performance concrete which uses palm oil clinker (POC), a waste by-product from the palm oil industry, as the lightweight aggregates.
Oil-palm-boiler clinker (OPBC) is an agricultural solid waste from the incineration process of solid wastes in palm oil industry. The OPBC that is highly porous and lightweight in nature is suitable to be used as a lightweight aggregate.
Utilizing waste material in the construction industry is an effective way to protect the environment and minimize construction cost. In this paper, palm oil clinker (POC) aggregates were used as coarse and fine aggregate replacement in lightweight concrete production.
of concrete added with oil palm shell as aggregate can be accepted for the production of structural lightweight concrete. This paper focuses on using palm oil clinker which having different properties with oil palm shell but both are waste from oil palm mill. The aim of this study is
This study gives the comparative analysis of polypropylene (PP)/oil palm flour (OPF) and PP/oil palm clinker (OPC) composites using maleated polypropylene (MAPP) as a coupling agent. Ground flour and crashed OPC were compounded separately into polypropylene with and without MAPP using a twin-screw compounder.
International Journal of Mechanical and Materials Engineering (IJMME), Vol.6 (2011), , 10-17 POTENTIAL OF PALM OIL CLINKER AS REINFORCEMENT IN ALUMINIUM MATRIX COMPOSITES FOR TRIBOLOGICAL ...
material in the palm oil industries is normally being dumped and treated as disposal waste thus creating environmental pollution. In this study, fine aggregate is replaced with palm oil clinker by 5%, 10% 15%, 20% and 25% by weight and compared with the conrol mix t prepared without palm oil clinker.
and manufacturers of palm oil products. The process of extracting the palm oil involved burning of fibers and husk inside the boiler under a high temperature. This process is to generate the steam engine for oil extracting process. The process of extracting the oil will also produce a waste product called palm oil clinker.
International Journal of Agriculture Innovations and Research Volume 1, Issue 1, ISSN (Online) 2319-1473 II. MATERIAL AND METHODS A. Palm Oil Clinker (POC) Fig.1. Palm oil clinker (POC) POC is a by-product of the burning of discarded husks, fibres and shells of the harvested oil palm fruit. These
palm oil clinker, 15% palm oil clinker, 20% palm oil clinker and 25% palm oil clinker respectively. Figure 2 . Variation of slump val ue of fresh concrete with palm oil clinker content It is observed that the slump value increases with increase in percentage replacement of sand with palm oil clinker for the same water cement ratio.
different percentage of palm oil clinker as a coarse aggregate replacement. This is to study the characteristic of palm oil clinker in concrete and as well as the changes that it makes in the strength of concrete. From the result obtained, due to its water absorbing characteristic, size and shape, palm oil clinker increase the bonding between
•A significant hump was observed in the angular 2θ range from 10° to 35°, representing an amorphous phase.•Palm oil clinker is a pozzolanic material.•Pozzolanic activity of palm oil clinker is higher than ground palm oil fuel ash. Journal. Construction and Building Materials – Elsevier. Published: Nov …
Malaysian Journal of Civil Engineering 29 Special Issue (2):241-253 (2017) ... In this study, Palm Oil Clinker (POC) obtained from palm oil industries was investigated for its possibility to be used as water absorbent material for the internal curing process of concrete.
Among the waste products, one of such waste by-product is the palm oil biomass clinker, which is a waste product from burning processes of palm oil fibres. Therefore, it is important to utilize palm oil biomass clinker as partial replacement of fine aggregates in concrete.
largest oil palm planted state, with coverage of about 1.2 million hectares (Wahid, 2006). Usu-ally, the fibber and shell are used as boiler fuel to produce steam to generate electricity for the oil palm mill operation. This burnt solid waste is called Oil-Palm-Boiler clinker (OPBC). Based on a survey, it is estimated that about 45,750m3 OPBC ...
©Copyright © 2018.Company EUG All rights reserved.sitemap